Leroys Lū‘au Lounge

Hi Tiki friends!

Firstly a quick introduction.

My names Leevi and I live in Australia. My wife started calling me Leroy as a joke which morphed into Roy.

I've been interested in tiki (in a broader sense) since I was a kid. Pretty sure it was watching Elvis movies in the back ground, my mum travelling to NZ in the 80s (coming back with stories) and finding all kinds of Polynesian tourist art at local markets.

What follows is a summary of the build so far from August 2018 to Jan 2019, 5 months in total. It's my first ever bar build.

Here we go…

The shed

We bought a new house in October 2016 which came with a 6m x 7m aluminium frame double garage. My mind immediately started ticking over considering options for a man cave / tiki bar / outdoor room.

• Here's what I started with
• Another photo

Wall cladding and insulation

After experiencing one summer in the garage with 40+ internal radiating heat I knew I would have to do some insulating before even considering building anything internal.

I opted to clad the internal walls with Yellow Tongue Flooring. It's pretty heavy and dense but it came in the perfect size sheets (3600x900x19) for minimum wastage. I could fit 6 full sheets along the back and 6 sheets on either side using the offcuts for other bibs and bobs. I figured with the density I wouldn't need wool insulation between the boards and outside aluminium sheeting. The yellow tongue also allowed the boards to click together flush.

Here's some pics:

• First sheet down
• First course down
• First side nearly done
• First side done!
• All walls done (video)!
• and a weird panorama

The wall cladding was pretty tough work. I mostly did it myself with some help from my wife when it came to lifting the more dangerous pieces.

The yellow tongue is 19mm thick which is more than strong enough to screw into when it comes to decorating.

I was pretty happy with the result

Building the bar

Next I tackled the actual bar. I planned to put it in the corner on wheels so it could be dragged in an out as needed. The idea was to make the bar the depth of normal shelves (540mm) so it wouldn't stick out to far.

• First I created the carcass out of 2x4 pine. I pocket hole screwed all the joints.
• I then tested the height of the raised section of the bar by temporality placing some some more 2x4s
• Adding the bar top gave me the actual height
• Which of course was too high. So I pulled everything apart and made some more cuts
• I used an old bench top from an inside reno for the bar top. The thought was to somehow paint or cover the top later.
• I experimented with capping the bench with bamboo poles
• Once I was happy with the height I started to add some details
• Finally I sanded enough poles to cover the front and sides.
• A girlfriend of mine owns a sign shop and she graciously printed up a large vinyl wrap which I stuck onto the bench.
• Final result Well kind of. I still have to stain / seal the top.[/url]

Bar Shelving

Part of the indoor reno involved removing some old shelving. Rather than throw it out I kept it for the shed. I'll eventually trim the bar with bamboo and add lighting. More on the lighting coming up.

• The shelves secured to the wall
• The bar slides in underneath nicely. The floor slopes down to the corner which is why there is a gap.

Lighting

I started searching for lighting on Gumtree and Facebook marketplace. I found some small bamboo tub lamps that I thought could do with some love.

• Original gross brown
• Stripped back to the frame
• Sewing a new shade
• Done.

Insulating the ceiling

Like I said at the start… the shed gets HOT! It's basically a giant heat sink that radiates down the stored heat from the sun. I considered a couple of options but in the end settled on Foilboard. Basically it's 25mm of polystyrene covered with foil. It acts as a reflective barrier and insulation. At $AUD50 a sheet it was going to be pretty expensive so I looked around and found it cheaper online. Bunnings matched the price and gave me 10% off which reduced the price to more like $AUD35. This was one material I didn't want to skimp on as I knew it would have the largest impact.

The number one reason why I chose Foilboard was becuase it was light and I could install it myself. I ended up using tech screws to attach directly to the top hats.

• First 3 panels up
• 12 to go
• 3/4 done
• Done

Adding the foilboard made a huge difference to the internal temp. It still gets hot on a 40℃ day but it's bearable. Truth be told on those days we'll probably be inside in the air conditioning. The only downside is that now I couldn't see where the top hats where so I'll have to get creative and use a pin to poke through when it comes to attaching the matting.

Dividing the shed

At some point it occurred to me that I didn't want to sit and look at all the workshop stuff while having a drink so I decided to halve the shed somehow.

We had some crappy old rubber backed curtains replaced inside the house. We were going to throw the old ones out but I rescued them (after they sat out in the rain for a week). Unfortunately they were getting mouldy so I put them through the washing machine with bleach to kill the mould and freshen them up.

• I think the came up alright
• I had to sew multiple curtains together to get the right width
• and the right height
• My original plan was to run the curtain track up and then down following the main support of the shed. This didn't work so well. The way the curtains hung was off.

Still I pressed on. My idea was to paint the curtains in a giant mural. I found some inspiration online and some really cheap and nasty pink paint from Bunnings.

• I rolled the paint onto the curtains with a roller
• Which gave me some decent coverage
• I planned to stencil the pink with monstera, birds of paradise and other tropical plants. Most of these plants are in gardens in our neighbourhood.
• More Stencils
• First test… This might work
• First curtain done
• Birds of paradise detail

More lighting

I'm a web developer in my day job and I've always like building things out of raw materials with my hands or software with my brain. A friend of mine is mad into Christmas lights so I asked him about it and he gave me a RapsberryPI and some individual addressable LEDs.

• LEDs
• The Pi and lighting controller
• Success… the wiring is good!
• Another Success… Controlling the lights with Falcon Player
• Testing how the Leds look in lamps

I plan on building multiple lighting sequences with xLights and controlling playlists with Falcon Player.

Curtains Part 2

After playing with lighting for a couple of days I came back to finish the curtains.

• I grabbed a few more greens from the local graffiti store
• Start with a dark green / blue outline
• Fill with green
• Highlight and spray in structure
• Done
• Relax

Remember when I said that:

My original plan was to run the curtain track up and then down following the main support of the shed. This didn't work so well.

Well I went back and decided to straighten the tracks.

• I cut a new frame from left over particle board
• Attached a new track
• and did a test hang of the curtains. The length was obviously off but that was easy to fix.
• Curtains drawn

That brings me to today

If you've read this far thank you. I hope you've enjoyed the journey so far! Let me know if there's anything you would change or I could have done better.

There's plenty more photos in the Google album which I'll continue to add to as I post more.

I'm also adding stories to my instagram if you want to follow that: https://instagram.com/leevigraham

My TikiBar build: Leroys Luau Lounge
Instagram

[ Edited by: leevigraham 2020-03-19 04:26 ]

[ Edited by leevigraham on 2022-03-13 20:38:02 ]

[ Edited by leevigraham on 2022-03-13 20:39:00 ]

[ Edited by leevigraham on 2022-03-13 20:47:04 ]

[ Edited by leevigraham on 2022-03-13 20:56:37 ]

[ Edited by leevigraham on 2022-03-13 21:31:02 ]

Quite the undertaking. Great to see another enthusiast pursuing the Tiki dream. Keep us updated!

On 2019-01-29 06:05, Donovan wrote:
Quite the undertaking. Great to see another enthusiast pursuing the Tiki dream. Keep us updated!

Yeah there's a lot of work. It might be done before 2020 :)

Great progress so far. What are you thinking for stain for the bar?

Ahoy from (almost) the other side of the world, fellow mustachioed tiki-ite!

First off, kudos on your amazing use of bamboo! I absolutely love the bar facade, it's got a perfect weathered look to it, like it's been in service for years. The cross hatching on the ceiling is a great touch too. I'd love to hear more about your process working with it, bamboo is one of the things I'd love to be able to make better use of.

Any plans to darken up the space during the daytime? Maybe hang some thick curtains behind the garage door (if you can without interfering)? In my first bar I had these heavy duty burlap-y curtains up because there was a lot of natural light, since I've moved to a basement it's an entirely different feel that's really let the lighting shine, if you'll pardon the pun. Of course, nothing wrong with taking advantage of the fact you live in the literal south pacific and just let the natural light dictate the brightness! The weathered bamboo look works great in the full sun so I think you're in a great spot either way.

It's clear how much work you've been putting in on this from the sequence of photos, and it really shows in the product. I often feel that the best tiki pieces are the ones we make by hand, both because then we've got a deeper connection to them and also because they have all the tiny details that make things interesting. The mural curtain is a great example of that. I don't know that I'm brave enough to have gone with the pink myself, but I certainly can't argue with the results. Fantastic job with everything you've done so far, it's already a great space and it still has tons of potential to be even better, depending on how far down the decoration rabbit hole you want to go.

On 2019-01-29 07:20, Sandbartender wrote:
Great progress so far. What are you thinking for stain for the bar?

Probably a clear varnish… maybe a light coat of honey stain first. I replaced a bench inside the house and did the same stain: https://photos.app.goo.gl/D7jMhzB3R3W9DJUG6

I'll probably trim the edge with thick rope to catch any spillages.

Happy to hear any suggestions!

On 2019-01-29 10:08, Mariner Mike wrote:
First off, kudos on your amazing use of bamboo! I absolutely love the bar facade, it's got a perfect weathered look to it, like it's been in service for years. The cross hatching on the ceiling is a great touch too. I'd love to hear more about your process working with it, bamboo is one of the things I'd love to be able to make better use of.

Thanks! I actually kicked off the project by buying 140 bamboo halves for $50 from a local swap and sell site.

They were pretty banged up so I've spent a lot of time sanding them back to remove the varnish. I started hand sanding then after about 10 poles went out an purchased a belt sander which made life sooooo much easier.

• Sanding
• Half sanded poles. I knew I was going to trim the tops

On 2019-01-29 10:08, Mariner Mike wrote:
Any plans to darken up the space during the daytime?

Depending on the heat I plan to keep the tikibar roller door closed. People will enter through the other garage door, close the door and then walk through the curtains. That should keep most of the natural light out. I'm also thinking of adding a water tank outside and hooking up a sprinkler system on the roof. That should keep the heat down and make it sound like it's raining outside.

On 2019-01-29 10:08, Mariner Mike wrote:
I often feel that the best tiki pieces are the ones we make by hand, both because then we've got a deeper connection to them and also because they have all the tiny details that make things interesting.

The arts and crafts part of tiki is a huge draw card for me personally… as well as the drinks.

On 2019-01-29 10:08, Mariner Mike wrote:
The mural curtain is a great example of that. I don't know that I'm brave enough to have gone with the pink myself, but I certainly can't argue with the results.

It was / is an experiment. The curtains are recycled and the paint only cost about $70 all up. It was worth a shot. When I light the bar if it doesn't look good then I'll probably reconsider and maybe change to roll up matchstick blinds like the roof.

[ Edited by: leevigraham 2019-01-29 14:12 ]

Ceiling update

I started working on covering the ceiling before the last post but the photos didn't upload. The plan for the ceiling is / was to cover the whole ceiling with some kind of matting hiding the silver foilboard. I considered a couple of options but finally settled on bamboo matchstick blinds from Spotlight. I chose these becuase

a) they come in 1800mm x 2100mm size which means I would only need 6
b) they are currently on clearance which means the are $20 each. To cover the whole ceiling would only be $120.

It turned out that they only had 4 1800mm x 2100mm which meant I needed to get 3 smaller widths to finish the job.

• I cut down some 700mm x 45mm timber to create battens
• then screwed them to the roof spacing them 600mm apart
• Then I stapled the matchstick blinds to the battens
• which looked pretty good But we can do better.
• Looking back towards the door. I'll eventually trim the overhang and figure out another way to hide the roller.

Taking some inspiration from BambooBen I wanted to add a bit more texture to the ceiling and give me a place to hand lamps and oddities.

• I crosshatched some bamboo halves and bound them together with jute twine
• Then I had a SC Mai Tai to cool down
• I trimmed a smaller section of the bamboo to fit to the point of the ceiling. As it turned out the spacing was perfect and all the squares have consistent spacing.

I replaced the fluro globes with power points which were unsupported so I build a couple of quick mounting boards out of spare yellow tongue and trimmed them with bamboo. I probably cover the points with a vinyl wrap so they blend in more during the day.

• Gluing on the trim
• Points mounted.

Lighting update

I moved the raspberryPi and lighting controller out the the shed to start testing the lighting. I ended up back lighting the bar first… which will probably change.

• Testing rainbow follow pattern. A bit full on for a tiki bar but a good test. Video Photo
• Then I tried a solid red with candle pattern in the lantern on the bar

There's more pics in the gallery if you're into detail.

Next steps are to finish the bamboo on the ceiling. I have to sand another 22 poles which I am not looking forward to.

Cheers Leevi

[ Edited by: leevigraham 2019-02-02 21:35 ]

Great progress! I'm enjoying your creative solutions to the challenge the shed space is offering. Please keep sharing!

On 2019-02-03 20:31, Prikli Pear wrote:
Great progress! I'm enjoying your creative solutions to the challenge the shed space is offering. Please keep sharing!

A challenge indeed… but it is essentially a blank slate!

Ceiling - Done!

This weekend I finally finished off the matting and bamboo on the ceiling. I had to sand another 18 half poles which was starting to get very tiresome so I built a simple sanding rig.

Here's a video

I also had 10m of led strip delivered which I thought I blew up immediately becuase I plugged a 5v strip into 12v… luckily I was able to fix them by cutting off the first LED… more on that next week.

[ Edited by: leevigraham 2019-02-18 02:48 ]

Hi all,

The build has continued and it's time for an update!

The last four months have focussed on lighting and finishing off the bar and shelves.

LED Lighting

Oh man have I learnt a lot about led lighting.

Luckily I have a friend who is crazy about christmas lights who helped me out with some hardware and a lot of advice.

I started with a 2x 5m 5v programmable led strips, a Raspberry Pi and a RPI-28D lighting controller which runs Falcon Player. I'll eventually be using xLights for light sequencing and show scheduling

First pass was to test the strips in my bedroom.

Here's a short video of the lamp testing.

Next test was to move the strip into the bar. I looped it over the top and ran a simple rainbow pattern (video).

Then I tested adding a short strip to the shelving.

Once I was confident with the electronics (I fried a few leds getting the voltage wrong), I took the shelves off and added strip to each individual shelf.

It was a real challenge to keep the voltage up over the whole strip length. The shelves have 420 leds… all individually programmable. I ended up injecting power for each stack of shelves.

Here's a video of a test sequence.

I also started experimenting with a fire sequence. Here's a video of testing xLights and the result

Eventually I got the shelves back on the wall:

and then I enjoyed a Mai Tai

Research

I was lucky enough to head to the UK for a month where I visited Trader Vics and The British Museum. Of course I had to try a Mai Tai and a Suffering Bastard.

I maxed out my duty free limit on J.Wray and Nephew OP.

Back home in Aus

I ordered a Tiki Dylan mug before I left and it arrived while I was away.

It goes perfectly with my other Tiki Dylan mug

I've started to collect a few different lights for the ceiling

including making my own glass float (I bought 8 bowls from a local website)

With so many moving parts I knuckled down and finished the bar top. I used a japan black stain and couple coats of varnish to add some protection. I also added trim to the front of the shelves.

While I had the stain out I ran a couple of tests on a few spare pieces of bamboo.

It's all coming together

The last step to finish off the bar and lighting was to add under bar lighting.

Pushing the rainbow for testing…

Here's a video of the fire effect and one of a reveal effect

Next steps

Now the base of the lighting is done i'm going to start working on the ceiling lighting. Stay tuned!

My TikiBar build: Leroys Luau Lounge
Instagram

[ Edited by: leevigraham 2019-06-15 07:58 ]

Looking good! I love the backlighting.

Great looking bar.

Groovy light effects! Very festive.

Today I hit another milestone at Leroys Luau Lounge… Lighting is all wired up!

Here's a video of the room and one walking around the corner.

I made few lampshades for lights

Next steps are to start programming some lighting sequences and hang a few glass floats.

I also managed to find an original tapa cloth from 1932. I'm planning on mounting it on the wall with a bit of focus lighting.

[ Edited by: leevigraham 2019-06-30 06:16 ]

Hi Roy. Love your bar! Fantastic work! Where did you get your LED’s from? I’m building a bar myself at the moment in the uk and I love the way you can program your lights!

On 2019-07-09 02:45, BIG SMOOTH wrote:
Hi Roy. Love your bar! Fantastic work! Where did you get your LED’s from? I’m building a bar myself at the moment in the uk and I love the way you can program your lights!

Hey BIG SMOOTH,

Here's a list of my setup and hot tips (in no particular order #braindump):

• If you're a complete noob (like I was / am) here's an excellent video
• I have a raspberry pi and rpi-28dplus to control the lights
• I have a 5v and 12v power supply to power the rpi-28dplus and lights. I power the lights directly from the controller.
• I use xlights to program the sequences. The plan is to load the sequences onto the raspberry pi and schedule it using falcon pi player.
• Buy 12v not 5v pixels and stripe. 12v require less power injection and are brigher overall (you know for lightning effects). I ended up with different voltages which is painful. I've blown leds accidentally plugining in the 5v strip to the 12v output on the board.
• My 5v strips have 60 leds p/m and are indivudally controlled
• My 12v strips have 48 leds p/m and 3 leds per pixel which means you control 3 leds at a time. Here's a similar 12v strip.
• I purchased multiple led connectors trying to figure out which were best. In the end I nearly always soldered 3 pin LED strip pigtail connectors to the strips. For longer runs between the lights I used cat6 (more on that next point) with this style of pigtail
• Cat6 is not recommended as it's only 24awg thick and solid core. If solid core breaks you loose your signal or power. I ended up soldering 2 cores to each pigtail wire effectively giving me a backup if one fails.
• This pixel tester saved me a bunch of hassle allowing me to quickly test my soldering on the 5v strips. It also works on the 12v strip if you use external power for the strip and don't plug in the usb.
• Canispater Christmas has an excelent youtube channel with heaps of information.
• Here's a good video on buying led strips

That shoud be enought to get started. Let me know if you have any specific questions.

[ Edited by: leevigraham 2019-07-09 06:11 ]

Hi Roy thanks for the info and the links. So Much useful much needed information. Il keep posted on my progress.

Really nice tapa!

Love the lighting!

But seeing how involved it is I think I'll just stick with the LED tape that's controlled by an infrared remote. LOL

On 2019-07-10 12:26, Sandbartender wrote:
Love the lighting!

But seeing how involved it is I think I'll just stick with the LED tape that's controlled by an infrared remote. LOL

It was a learning experience that's for sure. The end goal is to have a lightning / thunder storm roll through over the top of the music. I'll need to strobe the lights and then turn fade the music down and the rainstorm sound effect up. Also planning on adding a volcano, red lighting and smoke effects.

On 2019-07-10 11:12, W8N2Surf wrote:
Really nice tapa!

I'm planning on mounting it on the wall but it's going to take a lot of wall space. I need to figure out how to hanf things on top of it without damanging it too much.

Gorgeous lighting, but I'm really, seriously, blown away by that amazing vintage tapa. Wowzers! That's definitely a showpiece.

On 2019-07-11 08:48, Prikli Pear wrote:
Gorgeous lighting, but I'm really, seriously, blown away by that amazing vintage tapa. Wowzers! That's definitely a showpiece.

There's very few vintage tiki mugs in Australia from the early tiki-pop days… however we're very close (relatively) to the pacific islands so there is always real pacific island arts and crafts for sale.

Here's another tapa I'm looking at… it's 460cm x 580cm :o

HOLY CROWS! That is gorgeous!

A quick update,

Searching through Facebook Marketplace I saw a local garage sale which had this photo:

I saw the tapa and asked how much… the lady said I should see it first which was a good call becuase it had heaps of holes from bugs eating it. Clearly it had been stored in the garage for over 50 years. Regardless I offered $20 (probably $10 too much) and it was mine.

Last week I bought 6x cane lamp shades for $50 bargain*. The plan was always to give them a tiki upgrade. Here's what they looked like:

I pulled out the internal cylinder, trimmed up the tapa and stuck it on.

Here's the final result all lit up:

The holes can be clearly seen and the pattern isn't super strong but for $70 all up for 6x lights I'm still happy.

Another quick update. I decided to double down and complete all 6 lamps.

Here's a close up of some of the damage to the tapa:

I used the damaged pieces as scrap and tried to fill in the holes by glueing them on to the back of the better pieces.

Here's the result… all 6 done and dusted. Now to hang them and wire in more LEDs.

[ Edited by: leevigraham 2019-07-20 03:38 ]

scoring a damaged tapa is probably the best way to chop one up. I'd feel terrible hacking apart an intact and vintage piece. :)

Great new lights, really nice work.

A quick mid week update. I have two fridges in my tikibar atm… a large fridge (white) and mini bar fridge (silver). Even with the lights off a big white box is a bit of a distraction.

I contacted a friend of mine who owns a print shop and she printed me a few really large vinyl stickers to wrap the fridges.

They turned out amazing and I can't wait to get them on this weekend.

Mini fridge:

Large fridge:

Nice solution! Much better than the coat of paint I slapped on mine. :)

Fridges are done! No more white-white goods.

Minibar was a good test run.

Then I worked on the main fridge. The deep handles were a challenge but nothing some spray paint and off cuts couldn't fix.

those fridges turned out really well - and that's a great solution. I may have to sue that idea - well done!

The fridges look great!

Another day in Leroys Luau Lounge…

I decide to tackle a new light I bought of Facebook for $10. It's a fish trap style and I wanted to use the last of the old beetle hole tapa.

Here's the light in it's original state:

Not bad but we can do better.

First I made some repairs hot glueing offcuts to the back to cover the holes:

It's quite large so I had to do a bit of floor work to get started:

Lights up ok when there's other light in the room. I like that I can see the print as well as the illumination.

In pitch black I think I need stronger lighting for the bulb… The main issue is the overhang on the joins.

Regardless I'm pretty happy with the result. A little jute twine to bind everything together and…

Another milestone today… hanging the tapa… we'll kinda…

Plan it to carve some trim with a router and frame it all up… that can wait for next week tho. Time for a drink.

This weekends goal was to frame the tapa from last week with some custom trim.

I started with some NZ pine fence timber (4.2m in length) which a friend gave me. I drew out a simple geometric pattern and got to work with the router.

I created a simple jig to keep the base of the router flat near the edges.

The first couple of attempts were a bit wobbly but I figured with the eventual burning it would be ok.

My plant was to use a propane torch. We don't use roofing torches in Australia so the best I could find was a welders brazing torch at the local hardware store.

Unfortunately the torch didn't make much of an impact on the wood. It would have taken ages and cost a bomb in propane bottles. I returned the torch and got a refund.

Next idea was to get creative and use an old camp cooker to slowly burn the wood.

It worked ok… but it still would have taken too long and again cost a bit in butane canisters.

Time to go old school… Real fire to burn timber… who would have thought.

I ran the board over both hot coals and flame a few times

It seems the hotter the better. Flames really help get into the router lines, heat really chars the timber and brings out the grain.

Here's the result after the burn:

I then hit the whole thing with a wire brush which softened all the edges:

Final step was to give the whole thing a diluted coat of Jarrah stain and varnish. Another quick wire brush to bring out the ridges and boom…

Can't wait to get this up on the wall.

Nice work, looks great.

NICE! Love the ingenuity in finding a solution. In this case it just required going back to basics and it turned out beautiful.

Nice work all around - really like how your tapa light came out! thanks for sharing!

Looks great. Might have to do the firepit on my next round of trim. The torch takes too long!

On 2019-08-15 12:56, jimsflies wrote:
Looks great. Might have to do the firepit on my next round of trim. The torch takes too long!

What kind of torch do you have? I was still considering buying one to speed things up even more… but you said it still takes a long time.

This weekend invloved another round of carving and burning. I got pretty effiecient and managed to knock out about 8m of trim on a couple of hours just before the sun went down.

Sunset is the perfect time to light a fire and burn back the trim

I tried a few different burn techniques… in the end I think the best outcome came from the hottest flame and rotating the board 45 degress so the flame travelled up throught the routing groves. I also sprayed the board with water as soon as it was out of the fire to stop the edges burning too much.

My acual goal was to frame the tapa so I woke up relatively early (I won't say what time) and got to work.

I removed the placeholder timber and started from the top to support the tapa. The center post helped spread the tapa and kept it taught without stressing it.

I also did some repairs with a waterdowned wood glue. I figured that given tapa is mulberry bark a wood glue would bind the fibres well. Hopefully ti doesn't discolour the tapa too much.

I got the tapa mounted pretty quickly so I pushed it and decided to build out the next part of the project… a thin box to hide some lighting and fake plants.

I started with a frame made from scrap.

I squared everything up with some mdf board. I planned to use the board as backing for a covering. I wanted to get some Lauhala Matting for the box but it's really exoensive in Australia and hard to find so I went to the local hardware store and found some reed privacy screen.

I really don't like the reed screen… every time I've seen it on a fence it looks cheap (it is) but I decided to take a chance and thoight that if double it over it might be ok.

The mdf board was covered with spray paint (project with my daughters) and I didn't want that to show through so I bought some cheap black weed mat and covered everything.

I stapled the reed screen on trying to make sure any gaps where filled.

I then put the two boxes back in place and sat back for a r(hum) and ginger beer.

After a little bit of "inspiration" I decided to complete the goal and add the recessed lighting. I think it worked out well

Those fridges look awesome, very clever! I recently was given a mini version of that tall fish trap light and now I might modify it, haha.

I love all the lighting colors. Thank you for the time and effort to show us your work. You are a professional now. Good work, Wendy

On 2019-08-23 10:38, danlovestikis wrote:

I love all the lighting colors. Thank you for the time and effort to show us your work. You are a professional now. Good work, Wendy

Thanks Wendy! Coming from such a legend that means a lot. :)

A few updates from this weekend.

I found some old cane / bamboo furniture on Facebook Marketplace listed at $AUD 40 (about $US 27) which was an absolute steal. It filled out the space and made everything a bit more comfortable.

I expected that I would be entertaining a few friends so I prepared a few home made syrups:

• Cinnamon + Anise
• Coconut
• SC Demerara
• SC Mai Tai
• Pomegranate

I also organised a little rum tasting with a selection of rums in the bar which was quite fun.

It also turns out my wife is now coming around to the idea of a tiki bar and has requested we have friends around for her birthday in a few weeks :)

Love that furniture.